If you’re working on a computer and need to remove a stripped screw from a motherboard, don’t panic. With patience and the right tools, you can get that screw out and return to work in no time.
Most screws used in electronics are made of steel with a black oxide finish. The head of the screw is usually either a Phillips head or a flat head.
Over time, the screws can become stripped, making them difficult to remove. This guide will show you how to draw a stripped screw from a motherboard.
How to Get a Stripped Screw Out of Motherboard
Here are the supplies you will need to remove a stripped screw from a motherboard:
- A pair of needle-nose pliers
- A small flathead screwdriver
- A set of tweezers
- Isopropyl alcohol (70% or higher)
- A lint-free cloth or cotton swab
Begin by using the needle-nose pliers to grip the head of the screw. Apply pressure and turn the pliers in a counterclockwise motion.
If the head of the screw is completely stripped, you may need to use the flathead screwdriver to pry it out. Be careful not to damage the surrounding area while doing so.
Once you have removed the screw, use the tweezers to remove any pieces of metal or debris that may be left behind. Be sure to clean the area thoroughly with isopropyl alcohol and a lint-free cloth or cotton swab before proceeding.
How to remove stuck screw from a motherboard
What You’ll Need:
- A Phillips head screwdriver
- A hammer
First, try to remove the screw with a Phillips head screwdriver. If the head of the screw is stripped, you will not be able to remove it with a screwdriver.
If this is the case, you will need to use pliers. Place the pliers’ tip on the head of the screw and turn counterclockwise.
If the screws are still stuck, you may need a hammer. Place the flat end of the hammer on top of the pliers and tap gently until the screw comes loose.
The Stripped Screw Removal Process
First, you’ll need to gather a few supplies. You’ll need a screwdriver that fits the head of the stripped screw, a hammer, and a piece of metal (a nail or a paperclip will work).
Next, take the screwdriver and insert it into the head of the screw. Apply pressure to the handle of the screwdriver to get it started.
Once the screwdriver starts, use the hammer to tap on the handle. This will help drive the screwdriver further into the head of the stripped screw.
Once you’ve driven the screwdriver as far as it will go, take your piece of metal and insert it into the head of the screw next to the shaft of the screwdriver.
Apply pressure to bend the metal back and forth until you feel the Screw start to loosen. Once it’s loose enough, you should be able to remove it by hand.
Additional Tips and Tricks
- If the stripped screw is close to the edge of the motherboard, you may be able to use tweezers or needle-nose pliers to grip it and remove it.
- You can also try using a small drill bit to create a new hole next to the stripped screw. This new hole should be slightly smaller than the diameter of the stripped screw. Once you have made the new hole, you can use a screwdriver to remove the stripped screw.
You can use several methods to remove a stripped screw from a motherboard. However, it is important to note that some of these methods may damage the motherboard. As such, it is recommended that you consult with a qualified technician before attempting any of these methods.
Frequently Asked Questions
How do I get a stripped screw out of a motherboard?
The best way to remove a stripped screw is to use a screw extractor. A screw extractor is a tool that is specifically designed to remove screws that have been stripped.
To use a screw extractor, you will first need to drill a pilot hole into the centre of the stripped screw.
Once the pilot hole has been drilled, you can then insert the screw extractor into the pilot hole and turn it counterclockwise to remove the stripped screw.
How to get a stripped screw out of a monitor?
A few ways to get a stripped screw out of a monitor. One way is to use a drill bit to drill into the screw. Another way is to use a hacksaw to cut the screw.